Sold out
This is the harness used inside the cell pack assembly. There is a Molex 'Mini mi' series 20 pin connector that mates with SMC6 BMS PCB (01-5500 o...
View full details
This is the battery cell pack main power wires & connector that connects to the SMC6 BMS. RAST5 Connector to plug on the SMC6 BMS Black wire l...
View full details
Stain Gauge sensor used in all BionX motors Model MMF402255 350 Ohm +- 0.2% from Micro Measurement Comes with 2 pre-installed wire wrap sensors N...
View full details
Adapter - Power Connector: Old Docking - New Motor. Lets you connect an old battery dockink harness to a motor that uses the new Vpower connector.
Sold out
Adapter - Power Connector: Old Motor - New Docking. Lets you connect a new battery dockink harness with the new gold connector to a old motor that ...
View full details
Battery dock for DL battery only! Black, With DC ouput jack (for 6V lights). 01-5981 = New gold connector.01-5981-classic = Classic Connector. Not...
View full details
Battery docking station for all downtube batteries (DX & DV) except the smaller DL model. Black with classic motor connector (not latest gold p...
View full details
Docking station for all downtube batteries (DX & DV) except the smaller DL model 01-5253. Black With classic motor connector (not latest gold p...
View full details
Battery docking station for all downtube batteries (DX & DV) except the smaller DL model. Black - With new gold plated motor connector- With DC...
View full details
BionX Interface Box This tool is a USB to CAN bus converter. It is used with BBI software (BionX Bike Interface) in order to connect the computer t...
View full details
** RC3 and DS3 are only compatible with 48 volts batteries. (not 36v or less) This is an upgrade kit to replace older G1 or G2 controllers. The 01...
View full details
Sold out
June 2025: a few Keys # in stock, CONTACT if you see the key number you search for. KEYS # 2 3 3 5 23 28 28 41 46 48 5...
View full details
Sold out
BionX, BMS PCB Assembly, SMC5.2, with DCDC 6V accessory output - NO DB7 assembly 01-2999 Information needed when ordering this part;- The cell pack...
View full details
This is a charger for LiMn batteries (Lithium manganese). - 22.2v nominal voltage of the battery being. For 6S batteries. - 24.9v end of charge vol...
View full details
This is a charger for LiMn batteries (Lithium manganese). - 22.2v nominal voltage of the battery being. For 6S batteries. - 24.9v end of charge vol...
View full details
Sold out
BionX charger for Li-Mn batteries (Lithium Manganese)HIGH POWER model HP8204L2 - For 25.9v LiMn batteries. 7S (sometime seen as 24v or 26v) - Charg...
View full details
Sold out
This is a charger for LiMn batteries (Lithium manganese). - 37v nominal voltage of the battery being charged. For 10S batteries. - 41.5v end of cha...
View full details
Sold out
2023-03: Product sold out but a replacement is available here. BionX charger for Li-Mn batteries (Lithium Manganese)HIGH POWER model HP8204L3 - For...
View full details
Sold out
This is a charger for LiMn batteries (Lithium manganese). - 41v nominal voltage of the battery being charged. For 11S batteries. - 45.65v end of ch...
View full details
Sold out
This is the first BionX G1 classic controller. For CAN bus system (not for older I2C) There is no throttle lever on this one, only assist/regen le...
View full details
Hall sensor PCB assembly with hall sensor mounted on the flexible PCB + hard PCB section + 3 pin header. 2 pictured but only 1 sensor is included. ...
View full details
BionX DB7 Battery Cable assembly to be used with SMC6 BMS, 01-4287 Must be used with 6th generation BMS (SMC6.2, SMC6.3) The DB7 rubber used as a ...
View full details
DS3 color Display (3rd Generation color Display). Features include: Transflective color display Quarter-turn mounting mechanism Protective rubber ...
View full details
BionX Docking station assembly for DS3 display. Comes with; DS3 Docking with 3.5mm jack. Left and right plastic arms 3 set of shims with different...
View full details
BionX Docking Station for FRONT MOTOR bikes.Usually used on European TREK bikes. ONLY COMPATIBLE WITH FRONT MOTOR SYSTEMS. COMPATIBLE WITH G2 ...
View full details
Sold out
G1 'classic' Controller handle bar clip o'ring. Attaches to your bike’s handlebars and acts as mounting platform for the Bionx G1 (01-2331) conso...
View full details
BionX Docking Station for G2 controller. Receptacle only no G2 controller included. no clips, no rubbers, no screws, as pictured. A few length op...
View full details
Service Kit - Docking Station for all G2 controllers.Includes; 1x Console Receptacle. Different wire lengths available;. 01-4451, 10.7CM cable d...
View full details
BionX G2 throttle for Trek RIDE+ Pro bikes. - This throttle is usually used with Trek RIDE+ Pro controller.- Comes with a 2.5mm audio jack connecto...
View full details
Sold out
BionX IGH motor - 350W, 300RPM, 36 Spokes, Classic Connector, Silver, 01-3132 $999.99 CAD $599.99 CAD BionX IGH / Internal Gear Hub m...
View full details
Sold out
BionX IGH / Internal Gear Hub motor - 350W, 300RPM, 36 Spokes, 01-3132 BionX IGH 1st Generation motor, Internal Gear Hub with 3 speeds Nomina...
View full details
BionX Light Set, Complete Light Set with Harness. Battery docking with DCDC ouput requiered; produces a whopping 2000 lumens and 50 lumens off the ...
View full details
Cylinder lock used on Trek 'rear rack' bikes. Comes with the nut and 2 keys Only fit on Trek 3rd generation battery rear rack dockings Examples of ...
View full details
Sold out
BionX motor free hub body. 10 Speed, 3 pawls Two options available;- Part # 01-6198, M37 thread- Part # 01-6200 M42 thread * No removal tool provi...
View full details
BionX Motor PCB Assembly with external wires pre-installed. For D-Series motors (with plastic covers) and some IGH motors (Smart brand Internal Ge...
View full details
BionX Motor PCB Assembly with external wires pre-installed. For P, S, PL, PS Series motors (with metal covers) Is not compatible with D-series, Fr...
View full details