01-5560_20PIN - 48V Battery cell pack balancer plug harness for SMC6.X BMS
This is the harness used inside the cell pack assembly. There is a Molex 'Mini mi' series 20 pin connector that mates with SMC6 BMS PCB (01-5500 o...
View full detailsThis is the harness used inside the cell pack assembly. There is a Molex 'Mini mi' series 20 pin connector that mates with SMC6 BMS PCB (01-5500 o...
View full detailsThis is the battery cell pack main power wires & connector that connects to the SMC6 BMS. RAST5 Connector to plug on the SMC6 BMS Black wire l...
View full detailsStain Gauge sensor used in all BionX motors Model MMF402255 350 Ohm +- 0.2% from Micro Measurement Comes with 2 pre-installed wire wrap sensors N...
View full detailsAdapter - Power Connector: Old Docking - New Motor. Lets you connect an old battery dockink harness to a motor that uses the new Vpower connector.
Adapter - Power Connector: Old Motor - New Docking. Lets you connect a new battery dockink harness with the new gold connector to a old motor that ...
View full detailsBattery dock for DL battery only! Black, With DC ouput jack (for 6V lights). 01-5981 = New gold connector.01-5981-classic = Classic Connector. Not...
View full detailsBattery docking station for all downtube batteries (DX & DV) except the smaller DL model. Black with classic motor connector (not latest gold p...
View full detailsDocking station for all downtube batteries (DX & DV) except the smaller DL model 01-5253. Black With classic motor connector (not latest gold p...
View full detailsBattery docking station for all downtube batteries (DX & DV) except the smaller DL model. Black - With new gold plated motor connector- With DC...
View full detailsBionX Interface Box This tool is a USB to CAN bus converter. It is used with BBI software (BionX Bike Interface) in order to connect the computer t...
View full details** RC3 and DS3 are only compatible with 48 volts batteries. (not 36v or less) This is an upgrade kit to replace older G1 or G2 controllers. The 01...
View full detailsAugust 2028: Keys # in stock, CONTACT if you see the key number you search for. KEYS # 2 3 3 5 23 28 28 41 46 48 58 ...
View full detailsBionX, BMS PCB Assembly, SMC5.2, with DCDC 6V accessory output - NO DB7 assembly 01-2999 Information needed when ordering this part;- The cell pack...
View full detailsThis is a charger for LiMn batteries (Lithium manganese). - 22.2v nominal voltage of the battery being. For 6S batteries. - 24.9v end of charge vol...
View full detailsThis is a charger for LiMn batteries (Lithium manganese). - 22.2v nominal voltage of the battery being. For 6S batteries. - 24.9v end of charge vol...
View full detailsBionX charger for Li-Mn batteries (Lithium Manganese)HIGH POWER model HP8204L2 - For 25.9v LiMn batteries. 7S (sometime seen as 24v or 26v) - Charg...
View full detailsThis is a charger for LiMn batteries (Lithium manganese). - 37v nominal voltage of the battery being charged. For 10S batteries. - 41.5v end of cha...
View full details2023-03: Product sold out but a replacement is available here. BionX charger for Li-Mn batteries (Lithium Manganese)HIGH POWER model HP8204L3 - For...
View full detailsThis is a charger for LiMn batteries (Lithium manganese). - 41v nominal voltage of the battery being charged. For 11S batteries. - 45.65v end of ch...
View full detailsThis is the first BionX G1 classic controller. For CAN bus system (not for older I2C) There is no throttle lever on this one, only assist/regen le...
View full detailsHall sensor PCB assembly with hall sensor mounted on the flexible PCB + hard PCB section + 3 pin header. 2 pictured but only 1 sensor is included. ...
View full detailsBionX DB7 Battery Cable assembly to be used with SMC6 BMS, 01-4287 Must be used with 6th generation BMS (SMC6.2, SMC6.3) The DB7 rubber used as a ...
View full detailsDS3 color Display (3rd Generation color Display). Features include: Transflective color display Quarter-turn mounting mechanism Protective rubber ...
View full detailsBionX Docking station assembly for DS3 display. Comes with; DS3 Docking with 3.5mm jack. Left and right plastic arms 3 set of shims with different...
View full detailsBionX Docking Station for FRONT MOTOR bikes.Usually used on European TREK bikes. ONLY COMPATIBLE WITH FRONT MOTOR SYSTEMS. COMPATIBLE WITH G2 ...
View full detailsG1 'classic' Controller handle bar clip o'ring. Attaches to your bike’s handlebars and acts as mounting platform for the Bionx G1 (01-2331) conso...
View full detailsBionX Docking Station for G2 controller. Receptacle only no G2 controller included. no clips, no rubbers, no screws, as pictured. A few length op...
View full detailsService Kit - Docking Station for all G2 controllers.Includes; 1x Console Receptacle. Different wire lengths available;. 01-4451, 10.7CM cable d...
View full details